Engine

Details

Intake Manifold Type:
Dual Plane
Carburetor Quantity:
One
Carburetor Flange Type:
4-Barrel Square Bore
Material Type:
Aluminum
Finish:
Natural
Overall Height:
4.80"
Mounted Height:
4.27"
Port Height:
1.87"
Port Width:
1.15"
MFG. Part #:
2701
Sold in Quantity:
Each

Notes:

Edelbrock reccommends a 500-650 CFM carb.
GTIN Code:
085347027019

Info

Designed for 1986 and earlier 262-400 cubic-inch Chevys, the Performer EPS dual-plane manifold is optimized to deliver superior performance over other low-rise dual plane manifolds. This small-block Chevy manifold has a runner design thats "tuned" for peak torque around 3500 rpm on a 350-inch engine and it produces power from off-idle to 5500 rpm.

Dyno tests showed gains of 5 hp and 9 ft/lbs of torque over the standard Performer manifold on a 350 Chevy. From 3000 to 4500 rpm, the increases averaged 5+ ft/lbs. of torque for more performance where you need it most.

IMCA racing approved.

Item Details

IMCA Approved

Notes

Match with a dependable Edelbrock square-bore carburetor for maximum STREET performance gains.
Edelbrock reccommends a 500-650 CFM model.
Specs
Port exit dimensions: 1.15" x 1.87"
Carb pad height: 4.27"

Details

Intake Manifold Type:
Dual Plane
Carburetor Quantity:
One
Carburetor Flange Type:
4-Barrel Square Bore
Material Type:
Aluminum
Finish:
Natural
Overall Height:
5.08"
Port Height:
2.05"
MFG. Part #:
2716
Sold in Quantity:
Each
GTIN Code:
085347027163

Info

Now available for small-block Chevys with Vortec or Edelbrock E-Tec cylinder heads, the Performer EPS dual-plane manifold is optimized to deliver superior performance over other low-rise dual plane manifolds. The runner design is "tuned" for peak torque around 3500 rpm on a 350-inch engine and produces power from off- idle to 5500 rpm. Dyno tests showed gains averaging 5+ ft/lbs. of torque from 3000 to 4500 rpm for more performance where you need it most.

IMCA racing approved.

325-2716 Instructions (PDF)
Item Details
Plain Finish
IMCA Approved

Notes

Match with a dependable Edelbrock square-bore carburetor for maximum STREET performance gains. Edelbrock reccommends a 500-650 CFM model.

Will NOT fit under stock Corvette hood.

Specs
Port exit is 2.05" tall with slanted side walls
Carb pad height: 4.52"

Details

Intake Manifold Type:
Single Plane
Carburetor Quantity:
One
Carburetor Flange Type:
4-Barrel Square Bore
Material Type:
Aluminum
Finish:
Natural
Overall Height:
4.58"
Port Height:
1.90"
Port Width:
1.10"
MFG. Part #:
2975
Sold in Quantity:
Each
GTIN Code:
085347029754

Info

Edelbrock's Victor Series intake manifolds set the standard for quality and performance in the industry. This Victor Jr. unit is designed for 262-400 c.i. small block Chevy V8s operating in the 3500-8000 rpm range. These versatile manifolds are excellent for many applications from high-performance street to drag/circle track racing. They provide maximum performance for engines with standard port location, iron and aluminum cylinder heads.

All Victor Jr. manifolds offer extra material added for port matching and customizing, square bore carburetor flange, and water crossovers drilled and tapped for temp senders/bypass holes.

Notes

The low-profile of this intake works well in applications with minimal hood clearance and where 1" or 2" spacers can be used for performance tuning.
Right front has relief for dry sump pressure in lines.

Details

Intake Manifold Type:
Single Plane
Carburetor Quantity:
One
Carburetor Flange Type:
4-Barrel Square Bore
Material Type:
Aluminum
Finish:
Natural
Overall Height:
5.58"
Port Height:
1.90"
Port Width:
1.10"
MFG. Part #:
2999
Sold in Quantity:
Each
GTIN Code:
085347029990

Info

Designed for competition Small Block Chevy V8s used in all forms of racing, the Victor Jr. Tall intake manifold incorporates Edelbrock's extensive knowledge in induction technology. Victor Jr. Series manifolds provide excellent mid-range to top-end horsepower, resulting in race-winning performance. All Victor Jr. manifolds offer extra material added for port matching and customizing, square bore carburetor flange, and water crossovers drilled and tapped for temp senders/bypass holes.
Use the Victor Jr. Tall for the 3500-8000 RPM range when carburetor spacers are not allowed. This manifold is 1" taller than the regular Victor Jr. (at right) and also provides maximum performance for engines with standard port location, iron and aluminum cylinder heads.

Right front has relief for dry sump pressure in lines

Details

Intake Manifold Type:
Single Plane
Carburetor Quantity:
One
Carburetor Flange Type:
4-Barrel Square Bore
Material Type:
Aluminum
Finish:
Natural
Overall Height:
5.50"
Port Height:
2.00"
Port Width:
1.20"
MFG. Part #:
2925
Sold in Quantity:
Each

Notes:

Use Fel-Pro intake gasket #1205.
GTIN Code:
085347029259

Info

Edelbrock's Super Victor (3500-8500 rpm) is a high-performance, feature-packed racing manifold for standard port location 23-degree cylinder heads. A taller profile with extra long runners that extend into the plenum offers increased volume. The cross-sectional area of the runners are tuned to complement the runner length creating substantial torque increases at 4500-5500 rpm.

For Chevrolet 262-400 c.i. Small-Block V8. The Super Victor is designed for heads with standard port location and the runners match the "flat floor" entry of the latest 23° heads. It's about 1" taller than the Victor Jr., putting the carb pad height at 5-1/2" from end seals.

Slotted flange bolt holes to allow mating on decked blocks or milled heads

Rear water outlets allow custom cooling system routing
Flange above the intake ports is machined flat to provide a straight-line reference for port-matching layout
A boss for a distributor clamp has been added on the left side, for easier to access when timing an engine
Each runner has a nitrous boss to aid in fogger nozzle installation

Details

Intake Manifold Type:
Dual Plane
Carburetor Quantity:
One
Carburetor Flange Type:
4-Barrel Spread Bore
Material Type:
Aluminum
Finish:
Natural
Overall Height:
4.60"
Mounted Height:
4.05"
Port Height:
1.88"
Port Width:
1.14"
MFG. Part #:
2101
Sold in Quantity:
Each

Notes:

This intake will only work with pre '86 cylinder heads. Edelbrock reccommends a 500-650 CFM carb.
GTIN Code:
085347021017

Info

Edelbrock's famous Performer manifold is designed for street 1955-86 small block Chevys. This manifold is a stock replacement/street legal part for 302/327/350 V8s with OEM 4 bbl. or Edelbrock Performer Series carbs. Will also work on 1966-72 (1973 non-California) cars, 1966-83 trucks and Suburbans; except stock equipped EGR.

Performers accept late-model choke, waterneck, air-conditioning, alternator and H.E.I. Not for 1987 and later cast iron or Chevy Bowtie heads. Will not fit 1987 and later stock aluminum heads, due to the angle of the 4 center intake manifold bolts. 

Made in the U.S.A. 

NOTE: This intake does not work with kickdown kit 491-2350U.

Notes

Carburetor Recommendation: Edelbrock Performer Series carb, 500-650 cfm
Manifold height @ front:  3.50"
Manifold height @ rear:  4.60"
Carb pad height:  4.05"
Port exit dimensions:  1.14" x 1.88"

Details

Overall Length:
6.29"
Overall Width:
6.00"
Overall Height:
.91"
Gasket(s) Included:
Yes
Hardware Included:
Yes
Material Type:
Aluminum
Finish:
Natural
Sold in Quantity:
Each

Info

Adapts quad pattern to most 4-bolt 2 bbl. pattern. Gaskets and hardware included.

2-barrel patterns on centers:
5-1/8" x 3-7/16"
3-1/2" x 1-7/8"

4-barrel patterns on centers:
5-1/8" x 5-9/16"
4-1/4" x 5-9/16"
3-3/4" x 3-7/8"
Bolt Hole Pattern
2 bbl: (5-1/8" x 3-7/16") & (3-1/2" x 1-7/8"). 4 bbl: (5-1/8" x 5-9/16"), (4-1/4" x 5-9/16"), & (3-3/4" x 3-7/8").

Details

GTIN Code:
084663649455

Info

Phenolic material is a type of plastic resin which has excellent insulating properties, so it will keep the fuel in your 4 barrel Holley 4150/4160 cooler for more power. For 390 CFM carbs with 1.467" diameter bores.
Specially formulated material reduces heat conductivity 10 times greater than aluminum

Reduces fuel temperature inside the carburetor
Denser, more powerful fuel charge to the manifold
4 hole plenum design
1/2" height
Gaskets not included

Details

Overall Thickness:
.50"
Bolt Hole Pattern:
5.63" x 5.16"
Hole Diameter:
1.47"
Gasket(s) Included:
No
Hardware Included:
No
Material Type:
Phenolic
Sold in Quantity:
Each

Notes:

Includes dowel pins.

Info

Phenolic material is a type of plastic resin which has excellent insulating properties, so it will keep the fuel in your 4 barrel Holley 4150/4160 cooler for more power. For carbs with 1.467" diameter bores.
Fits Holley 4150/4160 bolt pattern
1/2" tall
4-hole design
1.47" bore
Phenolic construction reduces heat transfer and increases power